|
|
Join Date: Apr 2009
05-12-2010, 5:31 AM
|
Reply
|
What is your setup with the Krypt 8" Hlcd's? What cans and amp?
|
Join Date: Nov 2002
05-12-2010, 6:33 AM
|
Reply
|
I bought the cans from boardersmall and i have a Phoenix Gold OCTANE R 8.0:4 Amp putting out 250w rms bridged at 4 ohms.
they sound great but i think they can sound even better if i tune the settings on the crossover.
|
Join Date: Apr 2009
05-12-2010, 7:03 AM
|
Reply
|
Where can I get speaker terminals for the boardersmall cans?
|
Join Date: Nov 2002
05-12-2010, 7:20 AM
|
Reply
|
I got mine from radio shack for $5 a piece but you could probably contact ken and get them from krypt I think he had them for $3, www.diywake.com has them as well.
|
Join Date: Apr 2009
05-12-2010, 6:04 PM
|
Reply
|
Anyone else want to post their setup?
|
Join Date: Apr 2009
05-13-2010, 9:21 AM
|
Reply
|
I know more people are using the Krypt HLCD's?
|
Join Date: Nov 2002
05-13-2010, 9:45 AM
|
Reply
|
AJ it may be that a lot of people have just started getting the 8" since he recently started putting them up on ebay. I do know that there are a few people on the centurion and malibu sites that have put in the 6.5". I guess what i'm saying is that even though a lot of people have bought them, they might not actually have everything set up yet.
|
Join Date: Jun 2007
05-13-2010, 10:10 AM
|
Reply
|
^^^^^^^^That or they don't want to start getting bashed for having "knockoffs" . They guy who introduced those isn't to well liked here and any post with his stuff usually turns into hating threads.
Regardlesss I am not one of those people...............Any one of the cans from DIY, Aerial, Bullet Lines. I run the DIY wake stuff for my cans and racks. Solid solid product with great customer service. Most people put dynamat or some kind of sound dampening inside the cans to make them sound great. Without it you get a small echo if you ask me. The speakers just sound crisper wth the dynamat at least to my unprofessional ears. All the companies I believe have speaker can packages that get you the terminals, clamps and cans.
I did get to demo a Bullet Lines rotating rack and the rack/mechanism was top notch. I didn't have the cash to drop on two of them at the moment, but when I do I will def be getting 2 of them. Rock Solid design. So I can only assume their cans are of the same.
My Krypts sound great and do more than the trick for me. Would recommend them to anyone on a budget or looking to upgrade their old standard MB Quart speakers to HLCD's without dropping tons of dough.
As for an amp yu ocan't beat the pure power and quality of Kicker for the $$$ in my eyes. A ZX with your specs would def do the trick. There are some better quality amps for sure, but they cost quite a bit more. Again all depends on the budget, but Kicker is tough to beat, quality product for sure.
Last edited by xstarrider; 05-13-2010 at 10:14 AM.
|
Join Date: Jun 2009
05-13-2010, 5:48 PM
|
Reply
|
I have Krypt 8" HLCD's
Speakers sound GREAT when compared to my old skylons. You can actually hear the music while boarding now
Im running them in the bullet line cans, with a JL 6 channel, bridged ~150RMS per speaker. I plan to upgrade the amp soon so I can put these things to there 250W RMS potential.
My speakers came with a broken crossover, and grill. I emailed Ken and had new ones in just a few days at no cost. I am having an issue with a speaker can though, but I suspect he will take care of it.
+1 from me.
|
Join Date: Apr 2009
05-14-2010, 1:13 AM
|
Reply
|
Looks like I will be running two 8" Krypt hlcd's in the boardersmall cans powered by a Rockford Fosgate 400-4.
|
Join Date: Sep 2008
05-14-2010, 7:47 AM
|
Reply
|
Here is mine, I also got my cans for boarders mall. Two sets of 8s. Running at 2ohm via a Hifonics 1010. •RMS Power Output: 2 x 500 W @ 2 Ohms
They are super clean and super loud.
|
Join Date: Jul 2008
05-14-2010, 1:17 PM
|
Reply
|
Quote:
Originally Posted by ajholt7
Looks like I will be running two 8" Krypt hlcd's in the boardersmall cans powered by a Rockford Fosgate 400-4.
|
This is similar to what I plan to do, but with a Kicker 4 channel, bridged to 2. I snagged a pair of the speakers from eBay a few weeks ago, and just ordered the cans from BoardersMall.
|
Join Date: Nov 2002
05-14-2010, 9:20 PM
|
Reply
|
Duffy,
I'm jealous 2 pair with that type of power, those things should scream.
I'm getting my PAC lc-1 next week so I can control the tower speakers seperately. I cant wait to get out on the water again and have more fun with them.
|
Join Date: Mar 2006
05-15-2010, 6:10 AM
|
Reply
|
I have one set of the 8" driven by a KX450.2. Was hoping to have another set up but the amp I bought didnt work out. Glad to see some people actual got in on the discount when it was around. Damn good sound for the money.
|
Join Date: Sep 2008
05-15-2010, 9:00 AM
|
Reply
|
I put a simple dash switch in. It's on the amps remote on. That way I just turn them off. I've had bad luck with PACs. I have had 3 go out, I guess that's not to bad because they are cheap.
Last edited by duffymahoney; 05-15-2010 at 9:09 AM.
|
Join Date: Jun 2007
05-15-2010, 10:02 PM
|
Reply
|
Couldn't beat the deal. Thanks again J
|
Join Date: Sep 2008
05-17-2010, 12:59 PM
|
Reply
|
here is a picture of their new box that is coming out. It fits either 4-6.5 or cut larger openings and it will fit 4-8".
|
Join Date: Jan 2003
05-18-2010, 7:20 AM
|
Reply
|
Mine sound great. Can't beat the price.
|
Join Date: Jul 2006
05-18-2010, 7:28 AM
|
Reply
|
Jeff
Are those 8" or 6.5"
|
Join Date: Jan 2003
05-18-2010, 7:57 AM
|
Reply
|
Sorry, those are 6.5" in some cans a buddy of mine made.
|
Join Date: Sep 2008
05-18-2010, 9:41 AM
|
Reply
|
I am putting a pair of 6.5's in my buddies samson swivel cans. Sort of like a ghetto exile
|
Join Date: Jul 2006
05-18-2010, 10:47 AM
|
Reply
|
I was thinking of droping some in my stock Roswell speaker light bar comdo. I just didn't know if they were that much of an upgrade if I stuck with 6.5"
How loud are they at the end of the line? Can hear mine now but I want to HEAR IT if you know what I mean. Plus I would be adding another amp to power them.
|
Join Date: Sep 2008
05-18-2010, 10:50 AM
|
Reply
|
It would be night and day. You would need a proper amp that puts out 150 rms at 4ohm.
|
Join Date: Jun 2007
05-18-2010, 12:32 PM
|
Reply
|
Blair for sure even with the 6.5 it is a huge huge upgrade. Especially with those Kickers in the Roswells. For anyone who is thinking of upgrading the old 6.5 can guts to these it is a huge difference in clarity and volume while riding. You can hear so much more of the highs/low's and overall sounds.
|
Join Date: Jul 2008
05-21-2010, 12:32 PM
|
Reply
|
My BoardersMall cans just arrived, and I bought a Kicker ZX350.4 to power my pair. I'll be sure to post pictures when I get them mounted and wired up.
|
Join Date: Sep 2008
05-21-2010, 12:43 PM
|
Reply
|
Be careful with the cans when cutting the whole bigger. They scratch very easily.
|
Join Date: Jul 2006
05-21-2010, 1:36 PM
|
Reply
|
what did you use to cut the cans Duffy? My cans just arrived too. I read someone's post said it took him 5 minutes with a rotozip. My buddy went the jigsaw route and he had some probs. ...but I don't have a roto I only have a jigsaw...
|
Join Date: Nov 2002
05-21-2010, 1:55 PM
|
Reply
|
I used the jigsaw with a metal specific blade and was fine. I didn't look the best but you don't see that part anyways and yes they scratch super easy.
I'm still toying with the truck bedliner idea.
|
Join Date: Sep 2008
05-21-2010, 3:26 PM
|
Reply
|
I used a rotozip with a metal cutting bit.
|
Join Date: Dec 2009
05-21-2010, 4:35 PM
|
Reply
|
I installed two of the 6.5 krypt hlcd,s and am ruining them at 150 watts at 4 ohms and they are great for the money I also installed the real bullet 650hp coax in the interior and they are amazing if I did it again I would use the bullet hlcd,s as well
|
Join Date: Feb 2010
05-21-2010, 10:28 PM
|
Reply
|
i got two of the 6.5'' and have them in the bulletline pods , Just running them of a 5chnnl fusion amp but they still sound awesome .
|
Join Date: Jul 2008
05-26-2010, 8:07 AM
|
Reply
|
Yea, I just realized that I will have to cut the holes bigger - I figure I'll blue tape 'em up before I start cutting.
|
Join Date: Apr 2009
05-27-2010, 1:19 AM
|
Reply
|
Just cut my boardersmall cans. I just used painters tape and a jigsaw. Any scratches will be hidden by the speaker grills. Hopefully I can get a chance to install them next week.
|
Join Date: Jul 2008
05-27-2010, 8:02 AM
|
Reply
|
I did the exact same thing yesterday!
|
Join Date: Nov 2002
05-27-2010, 8:11 AM
|
Reply
|
Man, you guys are smarter than me. I wish i had thought of the painters tape, if i had done what you guys did I wouldn't have scratches on the ends of my cans.
|
Join Date: Jul 2008
05-27-2010, 11:52 AM
|
Reply
|
I think I want to have them powder coated, but before I do I want to get them installed and test fitted to see what they look like.
|
Join Date: Sep 2008
05-27-2010, 12:21 PM
|
Reply
|
I just took mine to a metal shop and had them re-polished. Cost me $20
|
Join Date: Apr 2008
05-27-2010, 2:29 PM
|
Reply
|
anyone know where I can get the 6.5 inch Krypt HLCDs? I can't find any on ebay... on the 8 inch ones.
|
Join Date: Apr 2009
05-27-2010, 2:32 PM
|
Reply
|
Bulletlines.com
|
Join Date: Apr 2009
05-27-2010, 2:44 PM
|
Reply
|
I just taped the outer edge that I was cutting. I left the rest of the cans covered in the bubble wrap they were shipped in.
|
Join Date: Oct 2007
05-27-2010, 2:56 PM
|
Reply
|
It also helps to put a few strips of painters tape on the bottom of the jig saw just to add a little more cushion. I had to do this to the 6 cans I did on the Kicker VLX with the KM6500.2 "6-Pack".
|
Join Date: Jul 2006
05-28-2010, 2:54 PM
|
Reply
|
just did mine. taped the top over the edge a little, left bubblewrap around the rest. metal blade on a jigsaw (18 tpi). took about 10 minutes. Easier than I thought...hopefully the rest goes the same. just bought velcro for crossover, hope to install over the weekend.
|
Join Date: Sep 2008
05-28-2010, 3:34 PM
|
Reply
|
|
Join Date: Aug 2006
05-28-2010, 3:59 PM
|
Reply
|
Hawk, get some "Great Stuff" insulating foam sealant to hold the Cross over in plase as well as pray a little around inside the can to absorb/reduce vibration.
|
Join Date: Jul 2001
05-28-2010, 4:20 PM
|
Reply
|
I have a pair of the 6.5's that dropped into some lightning cans I
had. I run four speakers in my boat on the front channels of a
720 watt soundstream and bridge the rear to the cans for 190
Watts to each. Sounds awesome. I had evids before and these are much
Louder and clearer.
|
Join Date: Jul 2006
05-28-2010, 5:28 PM
|
Reply
|
do I just spray the great stuff right over the crossover? won't hurt it? get it at any store?
|
Join Date: Dec 2009
05-28-2010, 7:39 PM
|
Reply
|
I mounted my crossover with spray foam as well spray a little in the bottom wait for it to expand then place crossover in and wait for the foam to harden wont hurt the crossover and is available at any home improvement store
|
Join Date: Jul 2006
05-28-2010, 11:53 PM
|
Reply
|
Harold what's on the inside of ur can? is that dynamat or somethin?
|
Join Date: Dec 2009
05-29-2010, 6:27 AM
|
Reply
|
yes it is deadbeat same thing as dynamat seems to work well keeping the sound above the interior
|
Join Date: Jul 2009
05-29-2010, 7:41 AM
|
Reply
|
I have a set of 6.5s that seem to be plenty loud in the boat, probably too loud but to be honest, they aren't really audible out on the line??? I thought maybe I needed to have them pointed out to the sides a bit. I'm running about 200W RMS to each speaker. Any thoughts?
|
Join Date: Dec 2009
05-29-2010, 9:39 AM
|
Reply
|
I am only putting 150 watts RMS to mine and can hear them clearly but my boats exhaust is super quiet I installed the malibu silent rider exhaust tips they are turned down and baffled or another option would be a FAE which is even quieter than the tips but would not work on my boat with the blade
|
Join Date: Aug 2006
05-29-2010, 10:12 AM
|
Reply
|
Hawk, you can go the dynamat route if you want to spend more money but just spiraling some foam around will deaden the vibration as well.
|
Join Date: Sep 2008
05-29-2010, 11:13 AM
|
Reply
|
Corbin,
How do you have your amp setup?
|
Join Date: Jul 2006
05-29-2010, 4:56 PM
|
Reply
|
Hate I totally was not thinking clearly when you mentioned "great stuff". I was in stereo mode and not thinking standard household product. Good stuff btw. So this is actually in place of the velcro...I like it. I didn't really like the velcro idea, especially since the back of the can is concaved so it would only hold on the four corners. This makes way more sense. I'm itchin for a new amp now--I must resist. Funny how this stuff can snowball in a hurry.
|
Join Date: Aug 2006
05-29-2010, 5:11 PM
|
Reply
|
Oh it snowballs!
Yeah skip the velcro I gaurantee the can gets hot and the adhesive heats up and your cross overs are floating around the can.
|
Join Date: Jul 2009
05-29-2010, 5:47 PM
|
Reply
|
As far as mounting the crossover - I used hot glue and glued it to the back of the magnet. I got the idea because I think I saw the new kicker 6000s have the crossover on the back of the magnet.
Duffy - I have a four channel amp bridged, still 4 ohms. The amp can't handle being bridged and then wired to drop it to 2 ohms, not that I have enough speakers to do that anyway.
|
Join Date: Apr 2008
05-30-2010, 4:20 AM
|
Reply
|
where do you guys set your eq or bass mid tweet settings on these. i have 6.5's in aerial speakers being powered by kicker 450.2 with a westsounds 420. great idea on the dynamat for the bottom side of the pods
|
Join Date: Apr 2008
05-30-2010, 4:36 AM
|
Reply
|
krypt 6.5's on a moomba OBV 07
Last edited by jmvotto; 05-30-2010 at 4:40 AM.
Reason: added pic
|
Join Date: Jul 2009
05-30-2010, 7:26 AM
|
Reply
|
Does it matter how far apart the speakers are?
|
Join Date: Jun 2010
06-01-2010, 8:48 AM
|
Reply
|
what's the best amp to power one pair of krypt hlcd 8"s?
|
Join Date: Sep 2008
06-01-2010, 9:08 AM
|
Reply
|
|
Join Date: Jun 2010
06-01-2010, 1:58 PM
|
Reply
|
duffy, i tried to look at the link but i couldn't open it.
|
Join Date: Sep 2008
06-01-2010, 2:12 PM
|
Reply
|
|
Join Date: Aug 2006
06-01-2010, 2:16 PM
|
Reply
|
Duffy he said "best" LOL
|
Join Date: Sep 2008
06-01-2010, 2:48 PM
|
Reply
|
Sorry I meant cheap but still pretty good
|
Join Date: Aug 2006
06-01-2010, 3:22 PM
|
Reply
|
Kinda like Bud Light right
|
Join Date: Jun 2010
06-01-2010, 8:19 PM
|
Reply
|
i've never heard that many good things about hifonix amps. how about something a little higher quality?
|
Join Date: Sep 2008
06-01-2010, 9:09 PM
|
Reply
|
Dude their amps rock! Read some reviews
|
Join Date: Jun 2010
06-02-2010, 8:12 AM
|
Reply
|
any other suggestions?
|
Join Date: Nov 2002
06-02-2010, 8:15 AM
|
Reply
|
earmark suggests the JL g1300 per pair of their bullet hollowpoint 7.7's
I would think that the same amp would pusth the krypts just fine.
it's 300 mono at 2 ohms.
|
Join Date: Jun 2010
06-02-2010, 8:25 AM
|
Reply
|
i was thinking about the jl g4500. anybody have any experience with this amp? i just really would like to get at least 250 x2 at 4 ohms for these speakers.
|
Join Date: Jun 2010
06-02-2010, 8:34 AM
|
Reply
|
so let me get this right. if i run a mono amp to two 4 ohm speakers, is that a 2ohm load on the amp? i know a lot of stuff in this world but nothing about audio.
|
Join Date: Nov 2002
06-02-2010, 12:29 PM
|
Reply
|
Yes, when wired in parallel.
Last edited by ldr; 06-02-2010 at 12:33 PM.
|
Join Date: Sep 2008
06-02-2010, 12:32 PM
|
Reply
|
I would love to test my amp against the JL. My system sounds super clean and super loud.
|
Join Date: Jun 2010
06-02-2010, 1:35 PM
|
Reply
|
well what about staying mono and going with the jl g1700 or a kicker zx 750.1 or an alpine pdx 600.1? any real difference between the three? how would they sound compared to the same speakers on a syn 2?
|
Join Date: Feb 2010
06-02-2010, 1:46 PM
|
Reply
|
None of the amps you just listed are full range amps. They are sub amps so they won't work for tower speakers. They would sound terrible compared to a SYN 2. You could use something like the JL HD750/1. It is a full range amp.
Last edited by willrice; 06-02-2010 at 1:50 PM.
|
Join Date: Jun 2010
06-02-2010, 2:00 PM
|
Reply
|
well dang. so what's some suggestions of how i can put around 250-300 watts to each speaker? has to be something less expensive than the syn2 that will give them the power they need. how about something in between the hifonics and the wet sounds in price and quality?
|
Join Date: Oct 2007
06-02-2010, 2:04 PM
|
Reply
|
Take a look at Kicker's new Class D full range IX500.4........250 x 2 @ 4 Ohm
|
Join Date: Jun 2010
06-02-2010, 2:29 PM
|
Reply
|
couldn't find a price on it. probably too new for where i was looking at. what about the zx650.4 or 850.2?
|
Join Date: Oct 2007
06-02-2010, 2:51 PM
|
Reply
|
Quote:
Originally Posted by redm1496
couldn't find a price on it. probably too new for where i was looking at. what about the zx650.4 or 850.2?
|
MSRP is about $499 on the Ix500.4
The zx650.4 is 325 x 2 and the zx850.2 is 295 x 2. Out of these two, the zx850.2 would be the better choice as it would be running at 4 Ohm.
|
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is On
|
|
|
All times are GMT -7. The time now is 11:10 AM.
|
|